|
|
|
|
|
|
| Illustration 1 | g02527297 |
| Specification for 283-6194 Stick Cylinder Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 241-7342 Bushing | During the press fit, insert the bushing in the cap assembly with the tapered side first. Outside diameter is 106.115 ± 0.011 mm (4.1777 ± 0.0004 inch). Installation depth of the bushing in the cap assembly is 9.85 ± 0.30 mm (0.388 ± 0.012 inch). |
| 2 | 1 | 7Y-4956 Locknut | Use any one of the following methods to tighten the locknut: Lubricate the threads of the locknut with 8T-9579 Oil all around before assembly. Torque the locknut to 15500 ± 800 N·m (11432 ± 590 lb ft). Lubricate the threads of the locknut with molybdenum disulfide all around before assembly. Torque the locknut to 11500 ± 600 N·m (8482 ± 443 lb ft). |
| 3 | 2 | 191-5604 Ring | Lubricate the inside diameter and the outside diameter of rings with clean grease. |
| 4 | 1 | 9X-3607 Seal As | Lubricate the inside diameter and the outside diameter of the seal with clean grease. |
| 5 | 1 | 191-5605 Ring | Lubricate the inside diameter and the outside diameter of ring with clean grease. |
| A | 1 | 283-6189 Cylinder As | Bore of the cylinder assembly is 170 ± 0.1 mm (6.7 ± 0.004 inch). |
| B | 1 | 242-6811 Rod As | Diameter of the rod is 114.93 ± 0.03 mm (4.525 ± 0.001 inch). |
| C | 1 | 358-8526 Head | Bore of head over two lands is 115.63 ± 0.03 mm (4.552 ± 0.001 inch). |
| 6 | 1 | 107-6933 Stop | Free linear movement of the stop after assembly is 0.50 ± 0.26 mm (0.020 ± 0.010 inch). |
| 7 | 2 | 095-0930 Retaining Ring | Maximum outside diameter of retaining rings after assembly is 81.0 mm (3.19 inch). |
| 8 | 1 | 231-6843 Seal Ring | The slit of the seal ring must turn in the direction of the piston. |
| 9 | 1 | 191-5644 Bushing | Outside diameter is 120.148 ± 0.032 mm (4.7302 ± 0.0013 inch). Thickness is 2.475 ± 0.025 mm (0.0974 ± 0.0019inch). |
| 10 | 1 | 324-9484 Buffer Seal | Lubricate the sealing lip of the buffer seal lightly with the lubricant that is being sealed. |
| 11 | 1 | 324-9486 U-Cup Seal | Lubricate the sealing lip of the U-cup seal lightly with the lubricant that is being sealed. |
| 12 | 1 | 209-5877 Lip Type Seal | Lubricate the sealing lip of the lip type seal lightly with the lubricant that is being sealed. |
| 13 | – | – | Apply green Loctite 609 to the wiper seal groove before assembly. |
| 14 | During the press fit, insert the bushing in the rod assembly with the tapered side first. Bushing is one of the following part numbers: | ||
| 1 | 241-7342 Bushing | Outside diameter is 106.115 ± 0.011 mm (4.1777 ± 0.0004 inch). Installation depth of the bushing in the rod assembly is 10.0 ± 0.5 mm (0.39 ± 0.02 inch). |
|
| 1 | 290-9183 Bushing | Outside diameter is 106.200 ± 0.013 mm (4.1811 ± 0.0005 inch). Installation depth of the bushing in the rod assembly is 10.0 ± 0.5 mm (0.39 ± 0.02 inch). |
|